TDMoG
The high density TDMoG card is applicable to O9400R CHAA with CC16 controller. This is one of the TDMoE family products developed by Loop after IP-6700, IP-6716, IP6763 and AM3440-TDMoE. This card would allow operators to transport up to 252E1 or 336T1 and Ethernet traffic over IP network. This allows cost effective migration to IP network from existing voice and data network using existing TDM based equipment.
 
Features
Hot pluggable interface card for O9400R
WAN Link
Two combo Gigabit Ethernet(GbE) with 2 RJ45 and 2 SFP housing
IEEE 802.3ad Link Aggregation
RSTP/MSTP
LAN Interface
Four 10/100/1000 Base-T Ethernet ports
Speed/Half/Full Duplex
Supports cross-connection from interface cards listed below:
CC16 card (STM-1/4/16 or OC-3/12/48)
STM-1/4 or OC-3/12 card
High density E1/T1 card
DS3/E3 card
High density Ethernet card
VLAN
VLAN ID support: Max. 4K
Support C-VLAN/S-VLAN tag adding and removing on Pseudowire
Assign VLAN based on MAC, IP, protocol or flow
VLAN based packet filtering
802.1q port-based VLAN
Support Q-in-Q
QoS
Ingress rate limiting per Ethernet port
Ethernet Network Level:
- 3-bit Priority Code Point-PCP field within 802.1P/802.1Q Ethernet frame-CoS
Packet classification with 8 queues per port
IP Network Level:
- 8 priority queues per port
- 6-bit DiffServ Code Point-DSCP field-ToS
Scheduling Algorithm
- Strict Priority (SP)
- Weighted Round Robin (WRR)
- Deficit Weighted Round Robin (DWRR)
Congestion Avoidance
- Random Early Detection (RED)
- Weighted Random Early Detection (WRED)
Pseudowire Capability
Support SAToP, SDH/SONET CEP, CESoPSN, MEF-8
Support VC4 transparent/channelized STM-1 and STS3C transparent/channelized OC-3
Support TDM traffic emulation over UDP/IP and Metro Ethernet Network
Backplane capacity up to 252E1/336T1
Maximum 512 Pseudowires
Up to 32 Pseudowires can apply Adaptive Clock Recovery (ACR) mechanism
Pseudowire Diagnostics Function
ARP, Ping and Trace Route
IP-MAC Table display
Pseudowire Information
Jitter and Wander
PDV compensation depth up to 128 ms
Jitter Buffer Size up to 256 ms
PPM version: conforms to G.823/G.824 traffic interface (+/- 1ppm)
Supports 1+1 card protection
Support 802.1d Mac learning: maximum 26K
Per port ingress rate limiting from 8kbps to 1Gbps
Rate-based and Priority-based rate limiting for LAN
Support 803.3x Flow control on input ports
Support 802.1D STP, 802.1w RSTP and 802.1s MSTP
Support IGMP snooping v2 (RFC 2236)
Timing sources
O9400R system clock
Adaptive mode: from WAN (GbE) port
External clock through Controller card
Interworking with Loop TDMoEthernet Series Products
IP6700, IP6702, IP6716 and TDMoE module on AM3440/O9500/O9550
Standard compliance: SAToP, CESoPSN, SONET/SDH CEP, MEF-8
RoHS compliant
Description
This is a high density TDMoG card to be used with O9400R. This is one of the TDMoE family products developed by Loop after IP-6700, IP-6716, IP6763 and AM3440-TDMoE. This card would allow operators to transport up to 252E1 or 336T1 and Ethernet traffic over IP network. This allows cost effective migration to IP network from existing voice and data network using existing TDM based equipment.
 
The O9400R-TDMoG module converts the TDM data stream and timing information from the PDH and SDH/SONET ports on the O9400R into packets through cross connection and transmits to the connected IP/MPLS* or Metro Ethernet network via dual combo Gigabit Ethernet WAN ports with 802.3ad Link Aggregation capability. Another Pseudowire device converts the received packet stream back to original PDH and SDH/SONET data stream along with the original timing information.
 
The card is hot-swappable and can be installed or removed from a Loop-O9400R chassis when the Loop device is powered up.
 
Applications
Downloads
File Type File Name Description
Brochure O9400R-TDMoG-v2-B Members only